This post attempts to explain how Huion tablet devices currently integrate into the desktop stack. I'll touch a bit on the Huion driver and the OpenTablet driver but primarily this explains the intended integration[1]. While I have access to some Huion devices and have seen reports from others, there are likely devices that are slightly different. Huion's vendor ID is also used by other devices (UCLogic and Gaomon) so this applies to those devices as well.

This post was written without AI support, so any errors are organic artisian hand-crafted ones. Enjoy.

The graphics tablet stack

First, a short overview of the ideal graphics tablet stack in current desktops. At the bottom is the physical device which contains a significant amount of firmware. That device provides something resembling the HID protocol over the wire (or bluetooth) to the kernel. The kernel typically handles this via the generic HID drivers [2] and provides us with an /dev/input/event evdev node, ideally one for the pen (and any other tool) and one for the pad (the buttons/rings/wheels/dials on the physical tablet). libinput then interprets the data from these event nodes, passes them on to the compositor which then passes them via Wayland to the client. Here's a simplified illustration of this:

Unlike the X11 api, libinput's API works both per-tablet and per-tool basis. In other words, when you plug in a tablet you get a libinput device that has a tablet tool capability and (optionally) a tablet pad capability. But the tool will only show up once you bring it into proximity. Wacom tools have sufficient identifiers that we can a) know what tool it is and b) get a unique serial number for that particular device. This means you can, if you wanted to, track your physical tool as it is used on multiple devices. No-one [3] does this but it's possible. More interesting is that because of this you can also configure the tools individually, different pressure curves, etc. This was possible with the xf86-input-wacom driver in X but only with some extra configuration, libinput provides/requires this as the default behaviour.

The most prominent case for this is the eraser which is present on virtually all pen-like tools though some will have an eraser at the tail end and others (the numerically vast majority) will have it hardcoded on one of the buttons. Changing to eraser mode will create a new tool (the eraser) and bring it into proximity - that eraser tool is logically separate from the pen tool and can thus be configured differently. [4]

Another effect of this per-tool behaviour is also that we know exactly what a tool can do. If you use two different styli with different capabilities (e.g. one with tilt and 2 buttons, one without tilt and 3 buttons), they will have the right bits set. This requires libwacom - a library that tells us, simply: any tool with id 0x1234 has N buttons and capabilities A, B and C. libwacom is just a bunch of static text files with a C library wrapped around those. Without libwacom, we cannot know what any individual tool can do - the firmware and kernel always expose the capability set of all tools that can be used on any particular tablet. For example: wacom's devices support an airbrush tool so any tablet plugged in will announce the capabilities for an airbrush even though >99% of users will never use an airbrush [5].

The compositor then takes the libinput events, modifies them (e.g. pressure curve handling is done by the compositor) and passes them via the Wayland protocol to the client. That protocol is a pretty close mirror of the libinput API so it works mostly the same. From then on, the rest is up to the application/toolkit.

Notably, libinput is a hardware abstraction layer and conversion of hardware events into others is generally left to the compositor. IOW if you want a button to generate a key event, that's done either in the compositor or in the application/toolkit. But the current versions of libinput and the Wayland protocol do support all hardware features we're currently aware of: the various stylus types (including Wacom's lens cursor and mouse-like "puck" devices) and buttons, rings, wheels/dials, and touchstrips on pads. We even support the rather once-off Dell Canvas Totem device.

Huion devices

Huion's devices are HID compatible which means they "work" out of the box but they come in two different modes, let's call them firmware mode and tablet mode. Each tablet device pretends to be three HID devices on the wire and depending on the mode some of those devices won't send events.

Firmware mode

This is the default mode after plugging the device in. Two of the HID devices exposed look like a tablet stylus and a keyboard. The tablet stylus is usually correct (enough) to work OOTB with the generic kernel drivers, it exports the buttons, pressure, tilt, etc. The buttons and strips/wheels/dials on the tablet are configured to send key events. For example, the Inspiroy 2S I have sends b/i/e/Ctrl+S/space/Ctrl+Alt+z for the buttons and the roller wheel sends Ctrl-/Ctrl= depending on direction. The latter are often interpreted as zoom in/out so hooray, things work OOTB. Other Huion devices have similar bindings, there is quite some overlap but not all devices have exactly the same key assignments for each button. It does of course get a lot more interesting when you want a button to do something different - you need to remap the key event (ideally without messing up your key map lest you need to type an 'e' later).

The userspace part is effectively the same, so here's a simplified illustration of what happens in kernel land:

Any vendor-specific data is discarded by the kernel (but in this mode that HID device doesn't send events anyway).

Tablet mode

If you read a special USB string descriptor from the English language ID, the device switches into tablet mode. Once in tablet mode, the HID tablet stylus and keyboard devices will stop sending events and instead all events from the device are sent via the third HID device which consists of a single vendor-specific report descriptor (read: 11 bytes of "here be magic"). Those bits represent the various features on the device, including the stylus features and all pad features as buttons/wheels/rings/strips (and not key events!). This mode is the one we want to handle the tablet properly. The kernel's hid-uclogic driver switches into tablet mode for supported devices, in userspace you can use e.g. huion-switcher . The device cannot be switched back to firmware mode but will return to firmware mode once unplugged.

Once we have the device in tablet mode, we can get true tablet data and pass it on through our intended desktop stack. Alas, like ogres there are layers.

hid-uclogic and udev-hid-bpf

Historically and thanks in large parts to the now-discontinued digimend project , the hid-uclogic kernel driver did do the switching into tablet mode, followed by report descriptor mangling (inside the kernel) so that the resulting devices can be handled by the generic HID drivers. The more modern approach we are pushing for is to use udev-hid-bpf which is quite a bit easer to develop for. But both do effectively the same thing: they overlay the vendor-specific data with a normal HID report descriptor so that the incoming data can be handled by the generic HID kernel drivers. This will look like this:

Notable here: the stylus and keyboard may still exist and get event nodes but never send events[6] but the uclogic/bpf-enabled device will be proper stylus/pad event nodes that can be handled by libinput (and thus the rest), with raw hardware data where buttons are buttons.

Challenges

Because in true manager speak we don't have problems, just challenges. And oh boy, we collect challenges as if we'd be organising the olypmics.

hid-uclogic and libinput

First and probably most embarrassing is that hid-uclogic has a different way of exposing event nodes than what libinput expects. This is largely my fault for having focused on Wacom devices and internalized their behaviour for long years. The hid-uclogic driver exports the wheels and strips on separate event nodes - libinput doesn't handle this correctly (or at all). That'd be fixable but the compositors also don't really expect this so there's a bit more work involved but the immediate effect is that those wheels/strips will likely be ignored and not work correctly. Buttons and pens work.

udev-hid-bpf and huion-switcher

hid-uclogic being a kernel driver has access to the underlying USB device. The HID-BPF hooks in the kernel currently do not, so we cannot switch the device into tablet mode from a BPF, we need it in tablet mode already. This means a userspace tool (read: huion-switcher) triggered via udev on plug-in and before the udev-hid-bpf udev rules trigger. Not a problem but it's one more moving piece that needs to be present (but boy, does this feel like the unix way...).

Huion's precious product IDs

By far the most annoying part about anything Huion is that until relatively recently (I don't have a date but maybe until 2 years ago) all of Huion's devices shared the same few USB product IDs. For most of these devices we worked around it by matching on device names but there were devices that had the same product id and device name. At some point libwacom and the kernel and huion-switcher had to implement firmware ID extraction and matching so we could differ between devices with the same 0256:006d usb IDs. Luckily this seems to be in the past now with modern devices now getting new PIDs for each individual device. But if you have an older device, expect difficulties and, worse, things to potentially break after firmware updates when/if the firmware identification string changes. udev-hid-bpf (and uclogic) rely on the firmware strings to identify the device correctly.

udev-hid-bpf and hid-uclogic

Because we have a changeover from the hid-uclogic kernel driver to the udev-hid-bpf files there are rough edges on "where does this device go". The general rule is now: if it's not a shared product ID (see above) it should go into udev-hid-bpf and not the uclogic driver. Easier to maintain, much more fire-and-forget. Devices already supported by udev-hid-bpf will remain there, we won't implement BPFs for those (older) devices, doubly so because of the aforementioned libinput difficulties with some hid-uclogic features.

Reverse engineering required

The newer tablets are always slightly different so we basically need to reverse-engineer each tablet to get it working. That's common enough for any device but we do rely on volunteers to do this. Mind you, the udev-hid-bpf approach is much simpler than doing it in the kernel, much of it is now copy-paste and I've even had quite some success to get e.g. Claude Code to spit out a 90% correct BPF on its first try. At least the advantage of our approach to change the report descriptor means once it's done it's done forever, there is no maintenance required because it's a static array of bytes that doesn't ever change.

Plumbing support into userspace

Because we're abstracting the hardware, userspace needs to be fully plumbed. This was a problem last year for example when we (slowly) got support for relative wheels into libinput, then wayland, then the compositors, then the toolkits to make it available to the applications (of which I think none so far use the wheels). Depending on how fast your distribution moves, this may mean that support is months and years off even when everything has been implemented. On the plus side these new features tend to only appear once every few years. Nonetheless, it's not hard to see why the "just sent Ctrl=, that'll do" approach is preferred by many users over "probably everything will work in 2027, I'm sure".

So, what stylus is this?

A currently unsolved problem is the lack of tool IDs on all Huion tools. We cannot know if the tool used is the two-button + eraser PW600L or the three-button-one-is-an-eraser-button PW600S or the two-button PW550 (I don't know if it's really 2 buttons or 1 button + eraser button). We always had this problem with e.g. the now quite old Wacom Bamboo devices but those pens all had the same functionality so it just didn't matter. It would matter less if the various pens would only work on the device they ship with but it's apparently quite possible to use a 3 button pen on a tablet that shipped with a 2 button pen OOTB. This is not difficult to solve (pretend to support all possible buttons on all tools) but it's frustrating because it removes a bunch of UI niceties that we've had for years - such as the pen settings only showing buttons that actually existed. Anyway, a problem currently in the "how I wish there was time" basket.

Summary

Overall, we are in an ok state but not as good as we are for Wacom devices. The lack of tool IDs is the only thing not fixable without Huion changing the hardware[7]. The delay between a new device release and driver support is really just dependent on one motivated person reverse-engineering it (our BPFs can work across kernel versions and you can literally download them from a successful CI pipeline ). The hid-uclogic split should become less painful over time and the same as the devices with shared USB product IDs age into landfill and even more so if libinput gains support for the separate event nodes for wheels/strips/... (there is currently no plan and I'm somewhat questioning whether anyone really cares). But other than that our main feature gap is really the ability for much more flexible configuration of buttons/wheels/... in all compositors - having that would likely make the requirement for OpenTabletDriver and the Huion tablet disappear.

OpenTabletDriver and Huion's own driver

The final topic here: what about the existing non-kernel drivers?

Both of these are userspace HID input drivers which all use the same approach: read from a /dev/hidraw node, create a uinput device and pass events back. On the plus side this means you can do literally anything that the input subsystem supports, at the cost of a context switch for every input event. Again, a diagram on how this looks like (mostly) below userspace:

Note how the kernel's HID devices are not exercised here at all because we parse the vendor report, create our own custom (separate) uinput device(s) and then basically re-implement the HID to evdev event mapping. This allows for great flexibility (and control, hence the vendor drivers are shipped this way) because any remapping can be done before you hit uinput. I don't immediately know whether OpenTabletDriver switches to firmware mode or maps the tablet mode but architecturally it doesn't make much difference.

From a security perspective: having a userspace driver means you either need to run that driver daemon as root or (in the case of OpenTabletDriver at least) you need to allow uaccess to /dev/uinput , usually via udev rules. Once those are installed , anything can create uinput devices, which is a risk but how much is up for interpretation.

[1] As is so often the case, even the intended state does not necessarily spark joy
[2] Again, we're talking about the intended case here...
[3] fsvo "no-one"
[4] The xf86-input-wacom driver always initialises a separate eraser tool even if you never press that button
[5] For historical reasons those are also multiplexed so getting ABS_Z on a device has different meanings depending on the tool currently in proximity
[6] In our udev-hid-bpf BPFs we hide those devices so you really only get the correct event nodes, I'm not immediately sure what hid-uclogic does
[7] At which point Pandora will once again open the box because most of the stack is not yet ready for non-Wacom tool ids